Loading...

Lamination Operator - 2nd shift

Laminator lays-up I/L cores with pre-preg and copper foil.  Utilizing heat and pressure the booked I/L cores are pressed to form a panel.  Under close to minimum supervision, depending on assigned job level and skill capability, the Laminator by applying one or more lamination skills will be able to process panels through the lamination operation per the designated Manufacturing Process Procedures.  Lamination skills are: flash route, breakdown, lay up, material preparation, and lamination press.  Other duties as assigned. This is a 2nd shift position with the hours of 3 - 11:30 PM, Monday - Friday. Some overtime may be required.

 

PRINCIPAL DUTIES AND RESPONSIBILITIES:

Material Prep: The material prep process is preparing all materials to be used in the lay-up process.

Process panels per Lamination MPP:

  • Monitor humidity in material prep room
  • Verify requirements of incoming materials to package label
  • -(Vendor, correct material, lot number, proper marking, thickness, size)
  • Monitor accuracy of materials inventory
  • Monitor usage of material by shelf life
  • Cut Prepreg, caps, copper foil, and tedlar as required
  • Drill lay up holes as necessary

 

Lay-up: Lay-up is the process of layering ("booking") the detail with the prepreg and the copper foil to create a book that will be placed in the lamination press.

Process panels per Lamination MPP:

  • Verify that all necessary materials are available prior to start of job lay-up
  • Lay-up panels per lay-up sheet and traveler
  • Verify bake cycle of details prior to lay-up
  • Clean caul plates with Time Saver
  • Monitor to insure uniform and constant flow of work through area
  • Verify humidity of lay-up room
  • Measure thickness of finished panels

 

Breakdown: The breakdown process is the final step after lamination to clean and prepare the panel for the next process.

  • De-pin and breakdown books
  • Clean resin from tooling holes, move to flash route for route after lamination
  • Measure panel thickness using micrometer
  • Brush panels for particles

 

Lamination Press: In the pressing stage the books are placed into the lamination press and subjected to extreme heat and pressure.  When subjected to heat and pressure in the lamination cycle the resin in the prepreg softens, flows, and becomes an adhesive.  When cooled, bonding of the copper foil, details, and prepreg form a panel.

Process panels per Multilayer Lamination MPP:

  • Verify press calibration
  • Verify proper vacuum pressure of press
  • Assure proper placement of books in press
  • Verify temperature and cycle time per traveler
  • Monitor to insure uniform and consistent flow of work through presses
Required Skills:
  • Able to understand and follow daily work direction and process instructions from supervisor or other qualified person in English
  • Ability to understand and follow posted procedures
  • Ability to understand and follow all safety codes
  • Must be able to communicate fluently in English, including basic reading and writing
  • Attention to directions and ability to focus on details

 

Physical/Mental Demands:

  • Must be able to regularly lift 50 pounds and carry materials
  • Must be able to stand for 8-10 hour shift

*Unicircuit is a drug-free facility.  All candidates must be able to pass a drug test.

Required Experience:

Experience: 0-2 Years Relevant Experience. Previous PCB experience preferred. Previous PCB lamination experience highly desired.

Must be eligible to work on defense and satellite programs subject to ITAR Regulations. Therefore, candidates must be a U.S. Citizen or a U.S. Permanent Resident ('Green Card').

Unicircuit is a VEVRAA/Federal Contractor and EEO/AA Employer, including disabled and veterans.

Location: Littleton
Category: Regular Full-time
Tracking Code: 2013130

Have questions? Let Us Know.

Contact Us

Need Help?

In accordance with the Americans with Disabilities Act and Executive Order 11246, Anaren provides reasonable accommodation to applicants with disabilities. Applicants who need different or additional accommodations for any part of the application and hiring process are encouraged to contact our Human Resources Department by calling 315-432-8909 or writing 6635 Kirkville Road, East Syracuse, NY 13057.

 

Anaren is an equal opportunity employer. All qualified applicants will receive consideration for employment without regard to race, color, religion, sex, sexual orientation, gender identity, genetics, national origin, age, disability or protected veteran status. Anaren is a drug-free workplace.